• how to hide entries from the endpoint tree list?

    Hi, i have installed Toolbox version 4.2. In the endpoint tree list of the data matrix are a lot of entries that are not of interest for me (e.g. all Biodegradation and Hydrolysis and Ionization entries under Genera...
    936528
    last modified by 936528
  • Create a group based on phy-chem property

    Hello, I am aiming to create a group at the Toolbox based on physical/chemical properties. For example, can I create a group of substance with surface activity values of 30-40 mN/m. Thank you very much, Hülya ...
    691276
    last modified by 691276
  • Still no QSARs in the Toolbox?

    In an earlier thread I believe it was stated that the publicly available QSARs that were in earlier versions of the Toolbox would be incorporated into V4.2. If this has been done I can't seem to access them; anyone u...
    601256
    last modified by 601256
  • QSAR Toolbox 4.2 server doesn't run the Windows Service

    Hi, I'm IT Admin. Research group of my comapny Told me to create a server to deploy QSAR toolbox. I used all the isntruccions following the Toolbox 4.2 Installation Manual. And the problem is that the Windows servi...
    Oscar Aullon
    last modified by Oscar Aullon
  • performance of category definition

    hi, i`ve installed TB 4.2 on Win10. I have checked all Databases and Inventories (to be sure not to miss any data), but after clicking Define under Category Definition it could take hours to find other chemicals. (e...
    936528
    last modified by 936528
  • export data matrix

    Hello, When exporting profiling data the info comes up always vertical even if I chose horizontal. Using v.4. Any tricks and tips? (vertical for me means the list of chemical is distributed vertically, I prefer to lo...
    956039
    last modified by 956039
  • v4.2: memory used by server is huuuuge!

    Hi all,   I recently installed v4.2 of the Toolbox (which explains why I'm writing on this forum!): just running the server takes 2.3 GB of RAM!! Is it normal? As my computer only has 4GB of RAM, that slows it d...
    Florian Gautier
    last modified by Florian Gautier
  • Error during toolbox v4.2 installation

    Hello,   While installing toolbox v4.2, I am facing below shown error. Can you please tell me a way to resolve this? I have been able to install till QSAR toolbox 4.2 database     Regards, Cheshta
    Cheshta Kapoor
    last modified by Cheshta Kapoor
  • Configuring toolbox to show data from US regulations only

    Hi, Is there a way to configure QSAR toolbox to show information pertaining only to USA regulations/inventories/databases and not show data from Japanese, European or other regulations? Selecting individual profilers...
    Cheshta Kapoor
    last modified by Cheshta Kapoor
  • Toolbox v4.2 installation

    Hello, While installing QSAR toolbox v4.2, PostgreSQL was installed. But after entering port no. as 5432 and password before database deployment, an error message shows-   Please help to resolve this issue. &#...
    Cheshta Kapoor
    last modified by Cheshta Kapoor
  • How to setup Toolbox Server service

    Hello,   When starting QSAR Toolbox Server using Services MMC or the QSAR Toolbox service controller the clients can't connect to the server whereas they can when the toolbox server is launched from its exe file...
    808799
    last modified by 808799
  • Database copy in V4.2

    There is a problem using the database copy utility with V4.2 of the Toolbox. When run you will get an error message, bottom left of screen to the effect that database "Toolboxv18" does not exist. In the Toolbox.Data...
    601256
    last modified by 601256
  • Documentation on the profiler for chromosomal aberration

    Dear all,   I read with interest the documentation on the profiler for "chromosomal aberration" and I am not 100% sure that I understood correctly the meaning of the columns of the table titled "Summary descript...
    439685
    last modified by 439685
  • Need help with Toolbox Client on Citrix

    Hello,   Our organization uses Windows 7 32 bits workstations so we've been unable to run TB4.1 client directly from the users computers. We installed the client part on a Windows 2008 R2 64 bits server and publ...
    808799
    last modified by 808799
  • 3D parameters

    Dear all,   First of all I wish to all of you a Happy new year.   Secondly I would like to kindly ask for some advice about 3D parameters computed by version 4.1 of the Toolbox. indeed, I did not succeed i...
    439685
    last modified by 439685
  • Number of conformers

    Dear all,   I took a look at the "Options" menu in order to see if there is a way to change the number of conformers that are computed by the 3D calculators. Unfortunately, I could not find out how to change the...
    439685
    last modified by 439685
  • QSAR toolbox 4.1, error when closing the program

    I have installed the QSAR Toolbox 4.1 on a windows 7 64-bit system.   I am finding when I am closing the QSAR Toolbox 4.1 Desktop Client Program I am getting an error "Toolbox.Desktop.Client has stopped working"...
    Ken Hockin
    created by Ken Hockin
  • Where are all the QSAR models

    Hi all,   Hopefully this problem isn't just for me, and someone can help!   I remember under version 3 (and previous) of the toolbox, there were QSAR models available under data gap filling for predicting ...
    697392
    last modified by 697392
  • CAN NOT CONNECT:toolbox4v13

    Dear all,   after installing the QSAR Toolbox 4.0, the Client does not start. The reason seems to be a connection problem to the database, because in the Server Window under Database it says CAN NOT CONNECT:too...
    1019315
    last modified by 1019315
  • hide entries in and scrolling through data matrix

    hi, a toolbox data matrix has the "rowheads" Structure, Parameters, Physical Properties ..., each expandadable. In older versions, a rightclick on a rowhead, then leftclick Hide was possible to hide the row. In ve...
    936528
    last modified by 936528